Research on the identification performance of UHF RFID system considering the correlation of cascaded channel

The identification rate of UHF RFID system was restricted by multipath propagation effects.The system identification performance was studied considering the correlation coefficient between forward and reverse channels.Based on the generalized Rician fading channel model,the analytical expression of identification rate was derived under independent,full correlation and correlation cases.Compared with the existing analysis,the proposed uniform calculation formula of identification rate was for any correlation coefficient and kinds of channel conditions.The numerical computation and Monte-carlo simulations show that the influences of different correlation coefficients,channel conditions,sensitivity and distance on the identification rate.     

Super-oleophilicity Co-doping Co2+/F-/TiO2 one-dimensional nanotubes for photocatalytic denitrification of light oil

In this study, a simple hydrothermal synthesis method was adapted for the preparation of Co-doping Co²⁺/F^-/TiO₂ nanotubes photocatalyst, and the micro-nano structure of catalysts prepared by biomimetic technology which makes the catalyst have super-oleophilicity property. Co²⁺/F^-/TiO₂ revealed improved photocatalytic performance for denitrification of light oil compared to single TiO₂ photocatalysts. The enhance of photocatalytic activity can be attributed to narrowing the band gap, increasing the light response wavelength and exposing more highly active crystal surfaces due to synergistic effects of Co²⁺ and F^? in the photocatalyst.     

15CrMoG钢棒材表面缺陷机理分析和工艺改进

分析得出,棒材表面细小纵裂纹和表面裂口缺陷产生于铸坯加热之前,且与结晶器弯月面保护渣有关。利用Thermo-Calc热力学软件计算15CrMoG钢凝固相变过程,结合亚包晶钢连铸凝固特点综合分析15CrMoG钢棒材表面缺陷的产生原因和产生机理。结果表明:15CrMoG钢在固相线温度附近发生包晶反应L+δ→γ和包晶转变δ→γ,不仅导致初生坯壳生长不均匀,而且加剧P、S元素在凝固前沿的偏析。而初生坯壳不均匀是导致棒材表面缺陷根本原因。棒材表面细小纵裂纹产生于结晶器内坯壳薄弱处,经过二冷和轧制工序在夹杂物和硫偏聚处扩展长大。棒材表面裂口缺陷是初生坯壳不均匀导致结晶器内液面波动大,造成铸坯夹渣所致。通过控制[C]0.16%～0.17%、[S]≤0.005%、保护渣碱度1.2、熔点≥1200℃、粘度≥1.0Pa·s,260 mm×30mm铸坯水量150 m³/h,拉速0.5 m/min等措施,裂纹合格探伤合格率由原45%提高至98%。     

课程群案例嵌入协同教学模式的探索

在课程群的教学中由于每门课程各自独立开展教学,缺乏知识的融合和衔接,导致学生运用综合知识解决问题的能力较弱。在课程群的教学中采用案例嵌入协同教学模式,将完整的工程案例嵌入到课程群各门课程的教学中,协同规划各门课程的教学任务,每门课程再围绕案例展开研究性教学。通过嵌入的工程案例衔接各门课程的知识点,帮助学生建构完整的知识体系,强化工程应用的概念；同时通过研究性教学,培养学生分析问题和解决问题的能力,两部分相结合,提高了学生运用综合知识解决复杂问题的能力。     

强化研磨加工中喷射角度对GCr15轴承钢板塑性变形的影响

利用ABAQUS有限元仿真软件研究不同喷射角度强化研磨加工GCr15轴承钢板过程的塑性变形,得到不同喷射角度与等效塑性应变沿真实路径距离的关系,并通过拉伸试验进行验证。喷射角度为90°的强化研磨加工伸长率为1.4%,相比未经过强化研磨加工的伸长率数值缩减了2.0%。断口收缩率由空白组的4.9%降低到喷射角为90°的2.2%。结合仿真和试验可知,强化研磨加工中喷射角度越大,塑性变形能力越低,材料加工越难。     

高强不锈钢绞线网与ECC黏结-滑移关系模型

高强不锈钢绞线网与ECC的黏结是二者协同工作的基础，且黏结 滑移关系模型是其黏结性能的综合反映，故通过对17组51个高强不锈钢绞网增强ECC薄板试件进行单边拉拔试验，研究横向钢绞线间距、纵向钢绞线直径和相对锚固长度等因素对钢绞线网在ECC中黏结性能的影响规律。试验结果表明，横向钢绞线的设置可使黏结破坏由脆性破坏转变为延性破坏；高强不锈钢绞线网与ECC的黏结滑移曲线可分为5个阶段，分别为上升段、微降段、延性强化段、下降段和残余段。基于试验结果，对钢绞线网在ECC中的黏结破坏特征和黏结 滑移机理进行分析，在相关黏结-滑移关系模型的基础上，提出钢绞线网与ECC的黏结 滑移关系模型，并进行模型参数分析。所提模型及模型参数计算公式与试验结果吻合良好，能较好地反映钢绞线网与ECC的界面黏结滑移特征。